
Electrical Repair & Troubleshooting

Electrical Repair & Troubleshooting in Maine
Dead outlets, breakers that will not stay on, lights that flicker when the furnace kicks in — Aces Highlands HVAC-Plumbing-Electrical finds the actual fault and fixes it. Licensed Maine electricians serving Portland, South Portland, Scarborough, Westbrook, Gorham, and Greater Portland.

Our licensed electricians pull permits and arrange inspections when the work requires them.
Call now to schedule electrical repair or troubleshooting: (207) 670-8616



Electrical Repair & Troubleshooting
Electrical troubleshooting is detective work. A dead outlet may trace to a tripped GFCI three rooms away; a breaker that keeps tripping may be a failing appliance, a nicked cable, or a worn-out breaker. We test rather than guess.
- Dead Circuits & Tripping Breakers
- Licensed Maine Electrician
- Diagnosed & Quoted On Site
To schedule electrical repair or troubleshooting, call (207) 670-8616.
Electrical Services We Provide
More capacity, and replacing older panels with a documented safety history (Federal Pacific, Zinsco).
Dealing with knob-and-tube or aluminum branch circuits, or running new circuits for a remodel.
New circuits, GFCI/AFCI code compliance, tamper-resistant devices.
Recessed, outdoor, and smart lighting, done to the right fixture rating for the location.
A dedicated 240-volt circuit sized under NEC Article 625.
Standby power with a code-compliant automatic transfer switch.
Electrical Repair & Troubleshooting
Flickering lights, warm outlets, nuisance tripping, and everything that falls under "something's not right."
Why Does My Breaker Keep Tripping?
A breaker trips for three reasons: overload, a short circuit, or a ground fault. Overloads are the common one — a space heater and a hair dryer on the same 15-amp bedroom circuit will trip it every winter morning.
A breaker that trips instantly with nothing connected points to a short or damaged cable. One that trips at random may be worn out — breakers age and trip below their rating. We test under load to tell the difference.
How Much Does Electrical Repair and Troubleshooting Cost in Greater Portland?
A troubleshooting visit that finds a failed breaker, tripped GFCI, or bad splice sits at the low end; tracing an intermittent fault through several boxes or replacing damaged cable runs higher, and panel or rewiring work is quoted separately.


How Much Does Electrical Troubleshooting Cost?
Most electrical repair calls in Southern Maine run $150 to $600. Finding a failed breaker, tripped GFCI, or a single bad splice sits at the low end; tracing an intermittent fault through several boxes or replacing damaged cable sits higher.
We quote after diagnosis and before the repair. If troubleshooting turns up a Federal Pacific panel or knob-and-tube an insurer will flag, we say so and quote it separately — never as a condition of fixing what you called about.
- A failed breaker, tripped GFCI, or bad splice sits at the low end
- Tracing an intermittent fault through several boxes runs higher
- Replacing damaged cable runs higher
- Panel or rewiring work is quoted separately
Call (207) 670-8616 to schedule electrical repair or troubleshooting.

About Electrical Repair & Troubleshooting
Portland-area homes make it interesting: knob-and-tube in West End and Munjoy Hill triple-deckers, cloth-wrapped cable from the 1940s, aluminum branch wiring from the 1970s, and thirty years of DIY additions in between. We have seen all of it.
Our electricians carry breakers, GFCI and AFCI devices, and splice hardware, so most faults are fixed in one visit. If the fix is bigger — a failing panel or circuits needing rewiring — you get a written quote, not a surprise.
Anything that smells hot, sparks, or buzzes is an emergency: shut the breaker off and call (207) 670-8616 now. For everything else, request a quote and we will schedule the next available visit.

When to Call an Electrician Right Away
You should call an electrician right away if you notice:
- Burning smell or scorch marks at the panel or an outlet
- Sparking, buzzing, or crackling from a panel or outlet
- Breakers that trip repeatedly or will not reset
- Partial power loss not caused by the utility
- Exposed, damaged, or overheating wiring
A burning smell, sparking outlet, or hot panel is a fire hazard — stop using the affected circuits and call us immediately.
Flickering Lights, Warm Outlets & When to Stop and Call
Most electrical repair calls fall into a handful of patterns. Knowing which one you're looking at helps you describe the problem — and know which ones can wait for a scheduled appointment and which ones can't.
Why Are My Lights Flickering or Dimming?
A brief dim when the well pump, heat pump, or dryer starts is usually normal voltage drop. Lights that flicker at random, or brighten in one room while dimming in another, are not — that pattern points to a loose neutral.
A loose neutral can push 240 volts onto 120-volt circuits and destroy electronics or start a fire. It may be in your panel, at the meter, or on Central Maine Power's side. Treat it as urgent and call today.
Why Did an Outlet Stop Working?
Start with the GFCI outlets — the ones with test and reset buttons in bathrooms, kitchens, garages, and outside. One tripped GFCI can kill every downstream outlet on its circuit, including ones in a different room. Press reset before you call.
If not, the usual cause is a failed backstab connection — a conductor pushed into a spring clip instead of wrapped around the screw. One loose clip kills everything after it; we find it and repair the run properly.
What Should I Check Before Calling an Electrician?
Reset every GFCI in the house, check the panel for a breaker sitting between on and off, and unplug whatever was running when the problem started. Note whether the fault is constant or intermittent, and which rooms are affected.
Do not open the panel cover, do not keep resetting a breaker that trips immediately, and do not use a warm or discolored outlet. Those are the calls we would rather take an hour early than a day late.
Flickering Lights: Three Different Problems That Look the Same
- One fixture flickers — usually the bulb, the socket, or the switch itself; the least urgent version.
- Lights dim briefly when a large appliance starts (AC compressor, well pump, dryer) — often normal voltage sag on an undersized circuit or service, worth mentioning at your next visit but rarely an emergency.
- Lights across the whole house flicker or dim randomly, unrelated to any appliance — this points at a loose connection at the panel or even the utility connection itself, and it's the version we treat as urgent, since a loose main connection can arc and heat up unattended.
Warm Outlets, Switches, or Panel Covers
An outlet, switch, or breaker that's warm or hot to the touch means current is meeting resistance somewhere it shouldn't — a loose wire connection, a failing device, or a connection carrying more load than it's rated for. This is one of the more reliable early warning signs of an electrical fire starting, precisely because it gives you a warning before smoke does.
A burning or ozone smell near an outlet, switch, or panel — even faint, even if nothing looks visibly wrong — is not a wait-and-see situation. Turn off what you safely can at the breaker and call. This is exactly the kind of call our 24/7 line exists for.
Why Breakers Actually Trip
A breaker tripping once, on an obvious cause (a space heater and a hair dryer on the same circuit), is the system working correctly. A breaker that trips repeatedly on light, routine loads — or one that trips with nothing obviously overloaded — usually means either the breaker itself is worn out (breakers do fail with age, just less often than the wiring around them) or there's a fault somewhere on that circuit's wiring.
We trace the actual circuit rather than swap the breaker and hope, since replacing a breaker on a genuine wiring fault just delays the same trip.
Dead Outlets and Partial Outages
A single dead outlet, when the breaker hasn't tripped, is frequently a failed GFCI upstream of it on the same circuit — GFCI outlets can cut power to everything downstream without tripping visibly themselves. Checking every GFCI outlet on the run (kitchen, bath, garage, outdoor) for a tripped RESET button is worth doing before assuming a bigger fault.
Sources: Maine Office of Professional Licensing — Electricians


Why Choose Aces Highlands for Electrical Repair & Troubleshooting in Greater Portland
We treat electrical work with the seriousness it deserves — whether it is a single home outlet or a full panel upgrade.
- Every connection is tight
- Every circuit is tested
- Our licensed electricians pull permits and arrange inspections when the work requires them
Safe, clean, and done right.
Electrical Repair & Troubleshooting FAQ

Proudly Serving Greater Portland and Southern Maine
Electrical repair and troubleshooting services available in:
• Portland • South Portland • Scarborough • Westbrook • Gorham • Falmouth • Cape Elizabeth • Cumberland • Windham • Standish • Gray • New Gloucester • Raymond • North Yarmouth • Yarmouth • Freeport • Pownal • Bridgton • Brunswick • Harpswell
If you don’t see your area listed, call (207) 670-8616 — chances are we can still help.

What Our Customers Are Saying
Trusted by homeowners across the Greater Portland area for quality workmanship, responsive service, and professional care.
Need Electrical Repair & Troubleshooting Today?
Panel upgrades, EV chargers, generators, wiring, and lighting for your home — done safely and to code by a licensed Maine electrician.
Call now to schedule electrical repair or troubleshooting: (207) 670-8616